The details for Ford Taurus and Mercury Sable car model is similar.
Exhaust System
CATALYTIC CONVERTER
Instructions are as follows :---
Removal & Installation
Left Side
Rear
Right Side
Car repair guide?
http://technoanswers.blogspot.in/2012/03/car-repair-guide.html
Exhaust System
CATALYTIC CONVERTER
Instructions are as follows :---
Catalytic Converter
Removal & Installation
Left Side
Specific to:
Ford Taurus 2008-2009
Mercury Sable 2008-2009
NOTE
Always install new fasteners and gaskets. Clean flange faces prior to new gasket installation to make sure of correct sealing.
- With the vehicle in NEUTRAL, position it on a hoist.
- Disconnect the Catalyst Monitor Sensor (CMS) electrical connector.
- Remove the exhaust Y-pipe.
- Remove the 2 catalytic converter support bracket-to-transmission bolts.
- Remove the 4 nuts and the LH catalytic converter.
- Discard the nuts and gasket.
- Inspect the exhaust manifold studs for damage. If damaged, replace stud(s), or if stud comes out when removing nut(s), replace the stud(s).
To install:
NOTE
Always install new fasteners and gaskets. Clean flange faces prior to new gasket installation to make sure of correct sealing.
- To install, reverse the removal procedure.
- Tighten exhaust manifold stud(s) to 18 ft. lbs. (25 Nm).
- Tighten the 2 catalytic converter support bracket-to-transmission bolts. to 35 ft. lbs. (48 Nm).
- Tighten the catalytic converter nuts to 30 ft. lbs. (40 Nm).
Specific to:
Ford Taurus 2008-2009
Mercury Sable 2008-2009
- With the vehicle in NEUTRAL, position it on a hoist.
- Remove and discard the 2 exhaust Y-pipe flange nuts.
- Discard the gasket.
- Loosen the Torca® clamp nut.
- Separate the catalytic converter from the muffler and tailpipe and remove the catalytic converter.
To install:
NOTE
Always install new gaskets and exhaust fasteners.
- To install, reverse the removal procedure.
- Tighten the Torca® clamp nut to 41 ft. lbs. (55 Nm).
- Tighten the 2 exhaust Y-pipe flange nuts to 30 ft. lbs. (40 Nm).
- Start the engine and check for exhaust leaks.
Specific to:
Ford Taurus 2008-2009
Mercury Sable 2008-2009
NOTE
Always install new fasteners and gaskets. Clean flange faces prior to new gasket installation to make sure of correct sealing.
- With the vehicle in NEUTRAL, position it on a hoist.
- Remove the exhaust Y-pipe.
- Remove the RH Catalyst Monitor Sensor (CMS).
- Remove the 2 bracket-to-RH catalytic converter bolts.
- Remove the 4 nuts and the RH catalytic converter.
- Discard the nuts and gasket.
- Inspect the exhaust manifold studs for damage. If damaged, replace stud(s), or if stud comes out when removing nut(s), replace the stud(s).
- Discard the nuts and gasket.
- Inspect the exhaust manifold studs for damage.
- If damaged, replace stud(s), or if stud comes out when removing nut(s), replace the stud(s).
To install:
NOTE
Always install new fasteners and gaskets. Clean flange faces prior to new gasket installation to make sure of correct sealing.
- Tighten exhaust manifold stud(s) to 18 ft. lbs. (25 Nm).
- Tighten the catalytic converter nuts to 30 ft. lbs. (40 Nm).
- Tighten the 2 bracket-to-RH catalytic converter bolts to 15 ft. lbs. (20 Nm).
This details will help.
Thanks.
FOR MORE HELP GO TO: ---
No comments:
Post a Comment